Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Granada Hills
Gate parts and welding in Granada Hills usually breaks down to one of three things: a hinge post that’s shifted, a rail that’s bent, or a frame that’s racked out of square. We fix all three on site, in your driveway, without hauling your gate back to some shop. Hal Gatewood has been running Gatewood Fence & Gate since 2001, and our crew covers Granada Hills from Balboa Boulevard up to the foothill streets off Rinaldi. Call (760) 361-6706 and a live person picks up, day or night.
Why Gatewood Fence & Gate Is Granada Hills’s Preferred Gate Parts & Welding Company
Most gate companies in the Valley want to sell you a new gate. We’d rather weld the one you have. On hillside streets above Knollwood Country Club, our crew was called for a “dead opener” on a 1980s swing gate. The real problem: the hinge post had shifted during the ’94 quake and never been releveled, racking the frame two to three inches out of square and binding the LiftMaster operator. We reset the post footing, squared the gate, replaced the sheared hinge bolts, and reinstalled the photo-eyes. No new operator needed. That’s the difference: we look for the post, not the upsell.
Hal’s name is on the shop and on every invoice. We publish our address. Our license number is there for anyone to look up. Granada Hills homeowners call us because they want a face they’ll see again at the hardware store on Chatsworth Street, not a different subcontractor every visit. The 90-Day Done Right Promise is stamped in writing on every job. If it’s not done right, one call brings us back.
We answer the phone 24/7. Not a voicemail, not a call center three states away, not a chatbot. When your gate is hanging off its hinges on a Sunday night during a Santa Ana, you talk to a person who knows Granada Hills and can get someone out.
Our Gate Parts & Welding Services in Granada Hills
Every job starts with the question: what actually failed? In Granada Hills, the answer is usually the post, the hinge, or the rail, not the opener. Fix those first and the gate works. Skip them and you’ll fix the same gate twice. Here’s what we do most often:
Hinge Replacement
Original hinges on 1950s and 1960s Granada Hills gates were built for lighter gates than what’s hanging on them now. Decades of Santa Ana gusts off the Santa Susana foothills have stretched pin holes, sheared bolt heads, and wallowed out mounting plates. We cut the old hinge off, weld a heavier barrel hinge in its place, and set the gate back to square. Most hinge replacements in Granada Hills run $180 to $420 depending on gate weight and how many hinges need to go.
Post Replacement
The post is the part everyone forgets until the gate starts dragging. Granada Hills has thousands of 1950s and 1970s ranch homes with original concrete footings. The 1994 Northridge earthquake, centered just a few miles away in Reseda, cracked and shifted a lot of them. A gate sags in the hinge post, not in the middle, and that’s where we start. We cut out the old post, break up the old footing, pour a new one with proper depth for the hillside soil, and weld the new post in place. Post replacement in Granada Hills typically runs $600 to $1,400 depending on footing size, fence type, and whether the post supports a slide gate or a swing gate.
Rail Repair
Slide gates on Granada Hills properties take a beating from October through December. The wind funnels through the Valley and slams unsecured gates hard enough to bend the rail, pop roller brackets, and throw the whole gate out of alignment. We straighten rails with heat and pressure when the steel is sound, and replace the rail section when it isn’t. Rail repair runs $250 to $750 in Granada Hills, depending on rail size, gate length, and whether the track needs resetting too.
Custom Welding
Some gates are worth saving because you can’t buy that style anymore. Ornamental scrollwork from the 1960s, hand-forged hinges, custom driveway-width frames: we weld those on site. We also build custom bracketry, reinforce weak welds on older gates, and fabricate replacement sections that match the original instead of looking like a patch. Custom welding in Granada Hills starts around $150 and runs up from there based on material and time.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Granada Hills
We’re certified to service nine major gate brands, including FAAC, BFT, Linear, and Viking. When an older FAAC board fails on a Granada Hills hillside gate, we can usually get the replacement part same week. For Linear and Viking operators common on Valley homes, we keep common boards and limit switches stocked on the truck. That matters when the Santa Anas are blowing and your gate won’t close. Less waiting, fewer trips, and you’re not paying for us to drive back and forth across the Valley.
Common Gate Parts & Welding Problems We See in Granada Hills Homes
- Northridge-shifted posts: Concrete footings from the 1950s through 1970s cracked in the ’94 quake and many were never releveled. The post leans, the gate racks, and suddenly the latch won’t catch and the opener binds. The fix is post reset, not opener replacement.
- Santa Ana-bent slide rails: Wind gusts off the Santa Susana foothills slam unsecured gates and bend the rail just enough that rollers skip, the gate jumps track, or the motor grinds against resistance. October through December is our busiest rail-repair season.
- Heat-warped wood and steel: Triple-digit Valley heat warps wooden gate frames and expands steel enough to bind operators and push photocells out of alignment. If your gate stops closing in August, the frame is usually the culprit, not the wiring.
- Latch and lock assemblies stripped by wind: A gate that slams in the wind eventually strips the latch bolt or bends the keeper plate. The gate looks closed but a strong push opens it, which is a security issue and a code issue in a fire zone.
Pricing for Gate Parts & Welding in Granada Hills, CA
Here’s what you can expect to pay in Granada Hills. Hinge replacement: $180 to $420. Rail repair: $250 to $750. Post replacement: $600 to $1,400 depending on footing work and gate type. Custom welding starts around $150. Full gate frame straightening and re-hanging typically runs $400 to $900. Every price is quoted and agreed before any work starts. You’ll know the number before we strike an arc. Estimates are free, and we’re glad to give a free second opinion on any written estimate you have. That includes seniors and veterans, who also get a permanent 10% discount on everything we do.
We Also Serve Cities Near Granada Hills
Our Gate Parts & Welding crew covers Granada Hills and the surrounding Valley communities, including San Fernando, Northridge, Sylmar, and Panorama City. If you’re a few blocks over the city line, call anyway. We’ll tell you honestly whether we cover your street and when we can get there. Most of Granada Hills is a short drive from our truck routes.
Serving Granada Hills, CA - Our Local Coverage Area
We’re based in the Granada Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Granada Hills
Because Granada Hills sits in a Very High Fire Hazard Severity Zone, Los Angeles Fire Department code requires automatic driveway gates to have emergency-access hardware like a Knox key switch so engines can open the gate without your remote. The remote working has nothing to do with it. If your gate doesn’t have the required fire access, you’re in code violation and it could also slow an emergency response to your own house. We check this on every automatic gate job in Granada Hills and install compliant hardware when it’s missing. Call (760) 361-6706 and we’ll tell you exactly what your gate needs.
Usually yes. The rail gets bent by wind gusts slamming the gate, and then the rollers can’t stay seated. We straighten the rail with heat where the steel is still sound, weld reinforcement plates where it has work-hardened, and reset the roller brackets. If the rail is too far gone or the track is cracked, we replace the section. Most Granada Hills rail repairs run $250 to $750 and we quote it before we start. Call (760) 361-6706 for a free estimate.
You check the post first. A gate sags in the hinge post, not in the middle. If the post is solid and the wood frame is just warped or soft, you may be able to replace the wood sections and keep the original steel work. If the post has shifted, which is common in Granada Hills because of the ’94 quake, replacing the wood alone won’t help. We’ll tell you which one is actually failing before anyone spends a dollar. Call (760) 361-6706 and we’ll come look.
Almost never. The opener is just fighting a frame that’s out of square because the post shifted. Most Granada Hills homes we see with this problem need the post footing reset and the gate re-squared before the opener will work cleanly. Replacing the opener on a racked gate is throwing money at the wrong part. We reset the post, square the frame, and then check the opener. If the opener is fine, you keep it. Call (760) 361-6706 and we’ll diagnose it properly.
The heat expands the steel frame and pushes the photo-eyes out of alignment, and it’s worse on west-facing gates that bake all afternoon. The fix is usually to correct the frame alignment and mount the photocells on brackets that move with the gate, not against it. Sometimes we also swap the older rigid mounts for adjustable ones. It’s a common Granada Hills summer repair and it usually runs $150 to $300. Call (760) 361-6706 for an exact quote. Estimates are free.
Call Gatewood Fence & Gate for Gate Parts & Welding in Granada Hills
If your gate is sagging, jumping track, or just not closing right, call (760) 361-6706. We’ll answer, ask what’s going on, and give you a straight answer about what it will take to fix it. Free estimates. Upfront pricing. The 90-Day Done Right Promise on every job. Hal Gatewood has been fixing gates since 2001, and his name is on the shop and on every invoice. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate. Hal has been welding and repairing gates across Los Angeles since 2001.