Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Granada Hills Homeowners
A gate that drags on the concrete, hangs at a crooked angle, or refuses to latch isn’t a minor annoyance in Granada Hills. It’s a security problem and a safety problem, usually caused by one worn hinge pin, a rotted post, or a broken weld. Here’s how much Gate Parts & Welding costs in Granada Hills, typically between $150 and $900, depending on whether we’re replacing a roller or rebuilding a post, and most repairs are finished the same day because we weld on site in your driveway.
Gatewood Fence & Gate has handled this work since 2001. Hal Gatewood answers his own phone, publishes his address, and stands behind every job with the 90-Day Done Right Promise in writing. You’ll deal with the person who owns the company, not a rotating crew. Call (760) 361-6706 and you’ll get a live person, any hour, any day.
Key Takeaways:
- Most gate parts and welding repairs in Granada Hills are completed same day with on-site welding
- Typical costs run $150-$900 depending on the part and the severity of the damage
- Hal Gatewood has repaired gates here since 2001, is licensed, insured, and publishes a real shop address
- Every job carries the 90-Day Done Right Promise in writing, not as a verbal handshake
- A live person answers the phone 24/7 at (760) 361-6706
What Our Gate Parts & Welding Service Includes
A gate fails at its weakest point, and after 29 years of looking at broken gates in the San Fernando Valley, San Fernando Gate Parts & Welding knows exactly where that point is. Here’s what we handle and how:
Hinge Replacement
When a gate sags, the first place to look is the hinge post, not the middle of the panel. Hinges carry the full weight of the gate every time it swings, and in Granada Hills, the combination of dry heat and occasional rain works the metal until it fatigue-cracks or the pin wears oval. We remove the old hinge, weld a new one in place, and realign the gate so it swings clean without dragging. This is the cheapest fix for a sagging gate, and it’s the one most often overlooked in favor of a full replacement quote.
Post Replacement
Steel posts rust at the base, where water pools against the footing, and wood posts soften underground where you can’t see it. A gate sags in the hinge post, not in the middle, and that’s where we start. We dig out the old post, set a new one in concrete, weld or bolt the hinges back on, and have the gate hung and swinging before the concrete finishes curing. Fix the panel without the post and you’ll fix it twice, which is why we don’t do that.
Rail Repair
The top and bottom rails are the backbone of a gate frame. When a vehicle bumps the gate or a kid swings on it, the rail bends or cracks at the weld joint, and the whole panel loses its shape. We straighten what’s straightenable, cut out and replace what isn’t, and re-weld the corners so the frame is square and strong again. A bent rail left alone will eventually crack through, and then you’re welding more than a rail.
Custom Welding
Some gates weren’t built for the opening they’re in, and some breaks happen in spots no off-the-shelf part will fix. That’s where on-site welding earns its keep. We bring the welder to your driveway, fabricate the bracket or brace the gate needs, and weld it in place while the gate hangs where it lives. No hauling the gate to a shop, no waiting a week for a panel to come back. Custom welding also covers ornamental iron repair, adding a section to widen a gate, and reinforcing weak corners that have cracked once already.
Gate Rollers
Slide gates ride on rollers that take a beating from dirt, grit, and the weight of the panel. When a roller freezes or the bearing goes flat, the gate starts grinding, shaking, and eventually refusing to move. We replace rollers with the right size and weight rating for your gate, set the track alignment, and adjust the guide wheels so the gate slides smooth instead of fighting the track. In the dry, dusty air around Granada Hills, roller bearings fail faster than most homeowners expect.
Latch & Lock
A latch that won’t catch or a lock that won’t turn means a gate that won’t stay closed, and a gate that won’t stay closed isn’t a gate. We repair and replace mechanical latches, bolt locks, and the strike plates they engage with, then adjust the alignment so the latch actually seats instead of bouncing. If your gate has an electronic lock tied to an access control system, we service that too, and we’ll show you where the alignment drifted before we call the job done.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
If your gate was built with FAAC or BFT hardware, you already know those parts aren’t sitting on a shelf at the big-box store. We’ve worked on FAAC swing and slide operators across Granada Hills for over two decades, and we stock the hinge kits, roller assemblies, and latch components these systems use. Same story with BFT; their equipment is precise and well-made, but when a part wears out, the fix has to match the spec or you’ll be back under the gate again in six months. We know the difference between a BFT motor mount that’s still square and one that’s been torqued out of alignment by a hit-and-run.
Linear and Viking systems show up a lot on older Granada Hills properties, and we keep common replacements for both. Linear’s slide gate rollers and limit switch brackets are two of the most frequent items we weld or swap, especially on long driveways where the gate gets opened six times a day. Viking’s heavier steel frames develop cracks at the corner welds after enough years of thermal cycling, and that’s a weld we do on site in under an hour. Whatever make your gate is, call us at (760) 361-6706. If we don’t stock the part, we’ll fabricate or order the right one, not a close-enough substitute.
Signs You Need Gate Parts & Welding Right Now
- The gate drags on the ground when you open or close it. This usually means a hinge has worn out or a post has shifted. Every drag pass scrapes more metal off the bottom rail, and the repair gets more expensive the longer you wait.
- You can see a crack at a weld joint. A crack never stops at the weld; it runs into the surrounding steel. In Granada Hills, where nights get cold and days get hot, that crack widens with every temperature swing.
- The gate wobbles side to side when you push it. That’s a loose hinge, a wallowed-out pin hole, or a post that’s started to lean. Show me the gate closing on its own and I’ll show you where it’s failing.
- The latch won’t stay latched. Wind and kids will find a gate that doesn’t positively lock. A latch that pops open on its own means the alignment is off, the spring is shot, or the strike plate has worn through.
- You hear grinding or screeching when the gate moves. That metal-on-metal sound is a bearing eating itself or a hinge pin running dry and chewing its sleeve. Grease might quiet it for a week, but the wear is already happening.
Our Gate Parts & Welding Process - Step by Step
We don’t show up, guess, and start cutting. Here’s how the work actually goes:
- 1
We look at the whole gate, not just the part you called about. The first thing Hal does on any gate parts or welding job is swing the gate by hand, watch where it binds, and check the posts with a level. A hinge that looks fine from the driveway can be the second failure point that broke the first one. You’d be surprised how often the visible break is a symptom, not the cause.
- 2
You get a written price before anything gets touched. We quote the job, you agree to the number, and that’s the number you pay. No “oh, we found more once we got into it” surprises at the door. If we find something while we’re working that genuinely needs attention, we stop and talk to you first, and you decide before we proceed.
- 3
We weld on site, at your gate, in your driveway. The gate stays where it hangs. We bring a generator-powered welder, grind the old weld, prep the steel, and lay a proper bead. That means no hauling a 300-pound gate off its hinges and no week-long wait for a shop to get around to it.
- 4
We replace the part, not the panel. If a hinge is worn, you get a new hinge. If a roller is flat, you get a new roller. We’re not going to tell you the only fix is a $4,000 new gate unless the gate is genuinely past saving. Repair-first is how we’ve worked since 2001, and it’s why customers in Granada Hills keep our number.
- 5
We test, adjust, and hand you the 90-Day Done Right Promise in writing. Before we leave, we open and close the gate a dozen times, check the welds for penetration, make sure the latch catches solid, and clean up the work area. Then we hand you a written promise that if it’s not done right, we make it right, one call brings Hal back.
How Much Does Gate Parts & Welding Cost in Granada Hills?
A typical hinge replacement in Northridge or Granada Hills runs $150 to $350, depending on whether it’s one hinge or a full set and whether the post needs any correction while we’re in there. Roller replacement usually lands between $180 and $400, with the higher end covering track adjustments and guide wheel work. Post replacement is the most variable: a steel post set in concrete runs $400 to $900, and that includes cutting out the old post, setting the new one, welding the hinges back, and re-hanging the gate so it swings true.
Custom welding jobs are quoted by the job, not the hour, and a straightforward crack repair or bracket fabrication typically falls between $200 and $500. What moves the price is access, the thickness of the steel, and whether we’re working on a single-family driveway gate or a commercial property. We don’t charge a trip fee inside the county, and we’ll give you a free second opinion on any written estimate you’ve gotten from another company. The best way to avoid overpaying is to know what’s actually broken before you accept a quote; that’s why our first visit includes diagnosis, and why the number we give you is the number you’ll pay. Call (760) 361-6706 for an exact quote. Estimates are free.
Gate Parts & Welding Near Granada Hills - Our Service Area
We work all over the Granada Hills area, including Sherman Oaks, Van Nuys, Tarzana, San Fernando, Encino, North Hollywood, Northridge, Sylmar, Reseda, Panorama City, and Chatsworth. Most homeowners get same-day service, and if you’re in one of the nearby communities, we’ll be at your gate with the welder in the truck, not a clipboard and a promise. You can read more about our work in the neighborhoods we serve on our Gate Parts & Welding in Granada Hills page or the Sherman Oaks service page. From Van Nuys to Northridge, the name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Serving Granada Hills, CA - Our Local Coverage Area
We’re based in the Granada Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Granada Hills
Gate parts and welding covers the repair and replacement of the structural and mechanical components that make a gate hang straight, swing smooth, and stay closed. That includes hinges, posts, rails, rollers, latches, locks, and custom-fabricated brackets or braces welded onto the gate frame. Instead of replacing the entire gate, we fix the part that actually broke, which is usually far less expensive and much faster.
Most hinge, roller, latch, and weld repairs are finished the same day, usually within two to four hours of arriving at your property. A full post replacement takes longer because the concrete needs time to set, though the gate is often hung and usable before the concrete fully cures. We’ll give you a realistic time estimate when we quote the job, and we don’t ask you to block out a whole day for a hinge.
Most repairs run between $150 and $900. The low end covers a single hinge or small weld repair, the high end covers a full steel post replacement with welding and re-hanging. Your exact price depends on what’s broken, how accessible it is, and the weight and construction of your gate. We quote the job before we start, and that’s the price you pay. No trip charge inside the county, and free estimates at (760) 361-6706.
Yes, we service all four brands and more. We’ve worked on FAAC and BFT operators across the San Fernando Valley since the early 2000s, and we keep compatible hinge assemblies, roller sets, and latch components in stock for Linear and Viking systems. If we don’t have the exact part on the truck, we’ll order the correct replacement, not a generic substitute that almost fits.
Yes. A gate that won’t close is a security issue, and a gate that won’t open traps your car in the driveway. We answer the phone with a live person 24 hours a day, 7 days a week, and we’ll get someone to your property as fast as possible. Same-day service is the standard for most Granada Hills repairs, not an upgrade you pay extra for. Call (760) 361-6706 and tell us what’s happening.
Every job we do carries the 90-Day Done Right Promise in writing. If something isn’t right within 90 days, one call brings Hal back to make it right, no runaround and no fine-print exceptions. That’s on top of the manufacturer’s warranty on any parts we install. It’s not a “up to” or an “in most cases” promise; it’s stamped on your paperwork.
You don’t need to do much. Clear the area around the gate so we have room to work, make sure the gate can be opened manually if it’s an automatic gate, and keep pets and kids inside while we’re welding. If you know the brand of your gate operator or the age of the gate, that’s helpful but not required. We’ll handle the diagnosis once we’re there.
Schedule Your Gate Parts & Welding Service in Granada Hills Today
If your gate is sagging, grinding, or holding on by a cracked weld, call (760) 361-6706 right now. You’ll get Hal or a member of his crew on the line, a straight answer, and a free estimate with no obligation. The gate stays in your driveway, the price is agreed before we start, and the work is backed by the 90-Day Done Right Promise. Seven days a week, any time of day, that number gets a real person who can help.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Granada Hills since 2001.