Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Van Nuys
Gate parts and welding in Van Nuys usually means one of two things: a sagging hinge on a 30-year-old retrofitted security gate, or a slide gate that’s stripped its rack and pinion teeth and stopped halfway across the driveway. We handle both, usually same day. Gatewood Fence & Gate has been handling Gate Installation - Van Nuys and repairs since 2001, and we stock the legacy hardware most shops stopped carrying years ago. If your gate is binding, dragging, or stuck, call (760) 361-6706 and talk to a live person who knows this neighborhood.
Why Gatewood Fence & Gate Is Van Nuys’s Preferred Gate Parts & Welding Company
This is Hal Gatewood’s shop. The name is on the truck, on the invoice, and on the door. We’re not a franchise rotating crews through the Valley. When you call about a gate repair in Van Nuys, you’re talking to someone who understands exactly what your gate is up against out here. The San Fernando Valley heat basin cooks gate operators in ways coastal LA never sees. A gate motor on a Van Nuys driveway sits above asphalt that can hit 150°F in July. That’s why our Gate Parts & Welding team carries heat-rated gear sets and upgraded circuit boards specifically for this area’s conditions, not whatever the warehouse had on sale.
Our customers in Van Nuys know the deal: we show up, we weld on site, and we don’t swap parts that don’t need swapping. Every job gets the 90-Day Done Right Promise in writing. If it’s not done right, Hal comes back. No runaround, no arguing about it. That’s how we’ve built our name across Van Nuys over the years, one driveway at a time.
Our Gate Parts & Welding Services in Van Nuys
Hinge Replacement
Hinge replacement in Van Nuys almost always starts with the post, not the hinge itself. Those 1960s concrete slabs under your gate posts have shifted over decades, and once the post leans a quarter inch, the hinge takes all the load. We cut out the old hinge, repair or replace the post as needed, and weld in new hinges that actually line up. The gate should swing like it did in 1995.
Post Replacement
When a gate post in Van Nuys has rusted through or pulled out of its footing, bolting on a patch isn’t going to fix it. We dig out the old post, set a new steel post deeper than the original, and weld it square. This is the repair that keeps a gate from sagging again in two years. We do it with the gate still in your driveway, not hauled off to some shop in another city.
Rail Repair
Slide gates on Van Nuys ranch-style properties and apartment complexes take a beating from the temperature swings here. Winter nights near freezing, summer days at 108°F. That metal expands and contracts constantly, and eventually the rail warps or the rack teeth strip. We straighten the rail, weld reinforcement where it’s needed, and replace the rack and pinion so the gate glides instead of grinding.
Custom Welding
Sometimes the part you need doesn’t exist anymore. When a 1990s wrought-iron gate in Van Nuys needs a bracket, a hinge plate, or a section of frame rebuilt, we fabricate it right there on site. Our welder works off the truck, so the repair happens same day. We’ve rebuilt everything from decorative scrollwork to structural gate frames in driveways from Sepulveda Basin to the airport corridor.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Van Nuys
We service and stock parts for most major gate operators, including Van Nuys Gate Motor & Opener systems, and we’re certified on nine brands including FAAC, BFT, and Viking. But here’s what matters for Van Nuys specifically: we keep legacy hardware on the truck. Doorking 1800-series parts, Elite SL-1000 components, older Viking control boards. A lot of shops in Sherman Oaks or Burbank won’t touch that stuff because it’s not in their system anymore. We carry it because a third of the gates in this zip code still run on it.
Common Gate Parts & Welding Problems We See in Van Nuys Homes
- Sagging hinges from shifting slabs: The 1960s-era concrete under most Van Nuys gate posts has cracked and settled, which throws the hinge alignment out and makes the gate drag. The operator motor then works harder every cycle until it burns out. Fix the post and hinge first, or you’ll replace the motor twice.
- Fried circuit boards from heat basin temperatures: A gate operator mounted over a Van Nuys driveway is sitting above asphalt that radiates 150°F on a hot afternoon. Boards and gear sets that would last 15 years in West LA die in five here. We stock heat-rated replacements and can relocate the operator housing if needed.
- Stripped rack and pinion from rail expansion: Slide gates in Van Nuys go through 80-degree seasonal temperature swings. The rail grows and shrinks, the teeth on the rack stop matching the pinion, and one day the gate just stops. We see it constantly on apartment gates off Vanowen and Victory.
- Solar opener battery failure on long driveways: Those ranch-style gates off Woodley Avenue and the Sepulveda Basin run on solar because pulling mains out there costs a fortune. But sustained 108°F heat kills battery chemistry fast. If your gate works fine in winter and dies by August, the batteries are cooked. We can tell you in one visit whether it’s batteries or the panel.
Pricing for Gate Parts & Welding in Van Nuys, CA
Hinge replacement on a typical Van Nuys swing gate runs $180 to $340, depending on how much of the post needs rebuilding. Post replacement is the bigger job, usually $450 to $900 with digging, concrete, and welding included. Rail repair with rack and pinion replacement typically lands between $350 and $700. Custom welding starts around $150 for small brackets and runs up from there for structural frame work. Every quote is verbal and written before any work starts. The price we quote is the price on the invoice, period. You’ll also get $40 off any repair over $200, no trip charge inside the county, and 10% off for seniors and veterans. Call (760) 361-6706 for a free estimate.
| Service | Typical Van Nuys Price Range |
|---|---|
| Hinge replacement | $180-$340 |
| Post replacement | $450-$900 |
| Rail repair with rack & pinion | $350-$700 |
| Custom welding (small bracket) | $150-$300 |
| Custom welding (structural frame) | $400-$1,100 |
We Also Serve Cities Near Van Nuys
If your gate is down in Sherman Oaks, Panorama City, North Hollywood, or Sun Valley, we’re already in the neighborhood. We run crews through these areas daily, so the response time is about the same as if you lived in Van Nuys itself. Give us a call and we’ll put you on the schedule. More about our local coverage in Gate Parts & Welding in Van Nuys.
Serving Van Nuys, CA - Our Local Coverage Area
We’re based in the Van Nuys area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Van Nuys
Your gate panel isn’t the problem. The post is. Van Nuys gate posts from 1960s-era retrofits are anchored into concrete slabs that have been shifting for decades, and the heat basin’s 80-degree seasonal temperature swings make it worse. Once the post moves a quarter inch, the gate sags and drags. Fix the post and hinge alignment first. Call (760) 361-6706 and we’ll confirm it on site before quoting a number.
Yes. We stock DoorKing 1800-series parts specifically because so many Van Nuys properties installed them in the early 1990s and they’re reaching end of life together. Motors, boards, and gear sets are still available if you know who to buy from, and we do. A lot of repair shops will tell you to replace the whole thing. We’ll tell you if a repair is actually the smarter call. Estimates are free.
Rail reinforcement and rack re-welding. The slide gates on ranch properties around Woodley Avenue and the Sepulveda Basin are wide, heavy, and exposed to full sun all day. The rail warps from the heat cycling, and the rack welds crack. We grind out the old welds, straighten the rail, and weld it back stronger than the original. This is our bread and butter out here.
Your batteries are likely heat-damaged. Van Nuys summers hit 108°F to 113°F, and sustained heat degrades battery chemistry fast. The gate works in winter because cooler temperatures let the battery put out more usable power. August is when it gives up. We can test the system and tell you whether you need new batteries, a larger panel, or a different operator. Call (760) 361-6706 and we’ll come out.
Yes, and you should have it regardless of what your old gate had. Any automatic gate installed or significantly modified in California needs photo eyes or contact edges to stop the gate if something or someone is in the path. Many 1990s Van Nuys retrofits never had it. When we weld in a new rack or replace an operator, we bring the Gate Access Control in Van Nuys safety side up to current code as part of the job. We’ll quote it upfront.
The Van Nuys Gate Parts & Welding Team That Actually Shows Up
The wave of automatic security gates installed across Van Nuys after 1992 built this whole neighborhood’s gate infrastructure. Those DoorKing 1800 and Elite SL-1000 operators are 30-plus years old now, and their hinge posts sit in concrete that’s moved an inch since the day it was poured. That’s the real story behind most gate failures here. On a ranch property off Woodley Avenue, we found a 16-foot solar swing gate where the original DoorKing hinge post had pulled three-quarters of an inch out of its footing. The sag was burning out the operator motor. We cut the old post, set a new steel post with a deeper footing, welded reinforcement plates at the hinge line, and installed a new rack and pinion drive with Van Nuys Liftmaster service-grade hardware and a fresh safety photocell. That gate cycles quietly now, even on 112°F afternoons.
That’s the kind of work we do for Van Nuys homeowners every week. The name is on the shop, the shop’s down the road, and that’s the oldest accountability there is. If your gate’s sagging, grinding, or dead, call (760) 361-6706. A live person answers, and Hal will be the one who shows up.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, fixing gates in Van Nuys and the San Fernando Valley since 2001.