Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across North Hollywood
Most gate failures in North Hollywood start with a part that was never spec’d for this climate. Hinge welds crack, posts pull loose from 1980s masonry, and operator boards cook in 112-degree Valley heat. Hal Gatewood has been fixing exactly these failures since 2001, and the fix usually happens in your driveway, not in a shop. If your gate is sagging, dragging, or refusing to close, call (760) 361-6706 for a straight answer and a free estimate.
Why Gatewood Fence & Gate Is North Hollywood’s Preferred Gate Parts & Welding Company
We show up with a welder in the truck. That’s the core of what we do, and it’s why North Hollywood property owners call us instead of a company that wants to haul the gate to a shop or sell a whole new one. Hal’s name is on the shop and on every invoice. His published address means you can find him after the job is done, which matters in a town where a lot of gate work was abandoned by contractors who are no longer in business.
Our Gate Parts & Welding team works throughout the Valley, and we know the difference between a post set properly in a poured footing and one bolted to a hollow brick pillar on a 1960s ranch home off Burbank Boulevard. We answer the phone with a live person at any hour, and the price we quote before work starts is the price you pay. Every job carries the 90-Day Done Right Promise in writing. If it’s not right, one call brings Hal back, no runaround.
Serving North Hollywood means dealing with gates installed during the 1980s and 1990s apartment and security boom, many of them retrofitted onto walls never meant to hold a 400-pound swinging steel gate. We’ve seen the same failure patterns hundreds of times, and we know what actually lasts here.
Our Gate Parts & Welding Services in North Hollywood
Hinge Replacement
Hinges take the entire weight of the gate, and in North Hollywood they take it while the gate is getting hammered by Santa Ana wind gusts and baked by summer heat. We replace hinge pins, barrels, and weld-on plates with stainless or hot-dipped galvanized parts sized for the panel weight. No spray-lube-and-wish-you-luck repairs. If the hinge is worn out, it gets a new one, welded on and greased correctly.
Post Replacement
This is the big one in North Hollywood. A gate sags in the hinge post, not in the middle. Posts set into 1980s masonry walls are frequently too shallow and under-spec’d for today’s operator torque, so repeated motor cycles literally rock the post loose from the wall. We cut the old post at the footing, re-core the masonry for proper embedment depth, weld in a new steel post, and re-hang the gate so it swings true. Fix the panel without the post and you’ll fix it twice.
Rail Repair
Sliding gates live or die by their rails and rollers. In North Hollywood’s fall wind season, Santa Anas push sliding gates off their bottom rollers and stress the upper rail guides until welds crack. We square the rail back to true, weld reinforcement plates where the stress concentrates, and replace rollers with bearing units that don’t seize in the heat.
Custom Welding
Some repairs don’t have a part number. Cracked iron pickets, torn operator brackets, and broken latch tabs all fall under custom welding. Hal welds on site, in the driveway or at the building entrance, so the gate never leaves the property. Work is done with the right filler, the right heat setting, and proper surface prep so the repair outlasts what was there before. If a gate has been “fixed” before by someone who globbed a weld over rust, we grind it out and do it correctly.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in North Hollywood
We regularly service gate operators and parts from Mighty Mule, DoorKing, and LiftMaster, three brands found all over North Hollywood’s apartment complexes and single-family driveways. A large share of the multi-unit properties along Lankershim and Magnolia still run older DoorKing entry systems, and we keep common wear parts in the truck so a service call doesn’t turn into a two-week parts-order wait. When a part is discontinued, we’ll tell you straight and show you the upgrade path before we touch anything.
Common Gate Parts & Welding Problems We See in North Hollywood Homes
- Santa Ana wind cracks hinge welds. The same gusts that knock over patio furniture flex lightweight aluminum gate panels until the weld at the hinge or the post fails. The gate then drops and binds on the latch side, which is why “adjust the hinges” never works for long.
- Valley heat seizes hinge pins. Powder-coated steel expands and contracts with the 105-degree temperature swings, and pins eventually seize. That puts bending stress on the operator arm, which then burns out motors. We replace seized pins and ream the barrels before damage spreads.
- 1980s post footings let go. Shallow footings in old masonry walls were never designed for modern swing-gate operators. The torque works the post loose over years, and one day the gate leans like it’s had enough. Re-coring and resetting is the only honest fix.
- Operator boards bake in the heat dome. Gate control boards mounted inside metal enclosures on west-facing walls effectively live in an oven from June to September. Capacitors bulge and fail. We mount or relocate boards with airflow in mind, not just “where the wire reaches.”
Pricing for Gate Parts & Welding in North Hollywood, CA
Here are the numbers we’re quoting on a typical North Hollywood repair call right now. Hinge replacement runs $180-$320 depending on how many hinges and whether we’re welding new plates. Post replacement runs $450-$900 when it includes re-coring the footing, which it almost always does on 1980s masonry walls. Rail repair runs $220-$400. Custom welding starts around $150 for small jobs and runs up from there. The price you’re quoted before work starts is the price you pay, in writing. We don’t do “found additional issues” surprises after the gate is apart. Call (760) 361-6706 and Hal will give you an exact quote, free.
We Also Serve Cities Near North Hollywood
Our service area reaches beyond the immediate neighborhood. We handle gate parts and welding regularly in Van Nuys, Sun Valley, Sherman Oaks, and Panorama City. If you’re anywhere around the Valley, the same crew, the same welder in the truck, and the same 90-Day Done Right Promise still apply.
Serving North Hollywood, CA - Our Local Coverage Area
We’re based in the North Hollywood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in North Hollywood
The inland heat is the difference. Santa Monica sits 15 degrees cooler on a 105-degree Valley afternoon, and that extra heat is what breaks down grease, seizes pins, and stress-cycles welds. Coastal gates rust faster from salt air, but North Hollywood gates fail from thermal stress, which is why we use high-temperature bearing grease and stainless or galvanized hinge parts here. Call (760) 361-6706 and we’ll tell you exactly what’s on your gate now and what to swap to.
Yes, and that’s the standard job for us. The trick is that the old post’s anchorage is usually the problem, so we can’t just weld a new post onto a failing footing. We cut the old post flush, re-core a deeper embedment into the masonry, set the new post, and weld it in place. The gate stays on the property, and we only tear out what’s already failed. Estimates are free; we’ll tell you if the pillar itself is sound before we start.
Santa Ana wind pushes the gates sideways and lifts the leading edge just enough to unseat cheap rollers. After enough flex cycles, the upper rail guides crack and the gate starts riding off track regularly. We weld reinforcement into the rail, square the guides, and install bearing rollers that stay seated under load. That fix holds, and it’s a lot cheaper than a new gate.
No, that’s a mounting and airflow issue. Older enclosures on south-facing or west-facing walls in the Valley get hot enough to damage the board. The welding side of the job is usually in the operator bracket and the hinge geometry, because a misaligned gate makes the motor work harder and run hotter. We’ll check both on the same visit. Call (760) 361-6706 and Hal’s crew can tell you if the board is still replaceable or if it’s time to upgrade before the gate stops entirely.
It means fixing the gate at the hinge post, not just cranking the hinges up and calling it done. The post is leaning because the footing or masonry anchorage has failed. We re-level the post or reset it entirely, then re-hang the gate so the latch side lines up with the post. Only after that does the operator get re-torqued and the close-limit adjusted. You can’t correct a sag by shoving a wedge under the leaf and hoping. Get a free second opinion on any written estimate, just call (760) 361-6706.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving North Hollywood since 2001.