Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across San Fernando
Gate parts and welding in San Fernando comes down to this: most of the wrought iron gates standing in this city were built between the late 1940s and the 1960s, and time plus San Fernando’s inland heat has done its work on them. Hinges fatigue. Posts rot at the base. Weld points crack under Santa Ana winds that funnel down the valley harder than most people expect. When a gate fails here, it rarely fails quietly. We fix gates on site, in the driveway, with a welding rig that comes to you. If you need Gate Parts & Welding in San Fernando, call (760) 361-6706 and a real person answers, day or night.
We know San Fernando’s streets. We know the permit counter at City Hall. And we know that a gate on a 1960s post in a tight shared driveway needs a different approach than a gate on a wide lot in Granada Hills. That local knowledge is why homeowners call us when the gate that held for 50 years finally gives out.
Why Gatewood Fence & Gate Is San Fernando’s Preferred Gate Parts & Welding Company
Hal Gatewood founded this shop in 2001, and his name has been on the door ever since. That matters in San Fernando, where people still check who they’re hiring before they hand over a key. The address is published. The license number is published. Hal will tell you himself: the name is on the shop, and the shop is down the road. That is the oldest accountability there is.
Our Gate Parts & Welding team has welded hinges back square on Kalisher Street, replaced post footings off Glenoaks, and rebuilt slide gate roller tracks near San Fernando High School. We stock common hardware for the narrow driveway openings this city is known for, which means less waiting on a supplier and more time with the gate actually back in service.
Every job gets written confirmation of our 90-Day Done Right Promise. If the weld cracks or the hinge binds within 90 days, one call brings Hal back. No runaround, no fine print. And we answer the phone 24/7. Not a voicemail. Not a call center three states away. A person who knows gates.
Our Gate Parts & Welding Services in San Fernando
Hinge Replacement
In San Fernando, a sagging gate usually isn’t a gate problem at all. It’s a hinge problem, and the hinge problem is usually a post problem. We see this constantly on the 1950s and 60s wrought iron gates that line the residential streets here. The hinge pin wears into an egg shape, the barrel loosens, and the gate drops a half inch until it drags on the driveway. We replace the hinge, weld a reinforced plate if the post face is thinned, and the gate swings true again. A typical hinge replacement in San Fernando runs $180 to $340 depending on gate weight and whether the post needs reinforcement.
Post Replacement
The hinge post is the gate. Not the panel, not the latch, the post. In San Fernando’s older homes, we regularly find posts set in original concrete from the Truman administration, cracked through and leaning under the weight of a solid iron gate. We remove the old post, core out the footing, set a new post in fresh concrete, and weld the hinges back on the same day whenever weather allows. Expect to pay $450 to $900 for a full post replacement here, more if the adjacent walkway or wall was built around the post and needs careful hand excavation.
Rail Repair
Rails are the horizontal bars that hold the pickets together, and on San Fernando’s older gates they fail in predictable places. The bottom rail rusts first, usually where sprinkler water from those small front lawns soaks it every morning. The top rail takes the twist when someone pushes the gate open by hand instead of using the opener. We cut out the rotted or cracked section, sleeve it, and weld in a replacement that matches the profile. Most rail repairs in San Fernando run $150 to $400 per rail depending on length and access.
Custom Welding
Some of the gates we work on in San Fernando were custom built 60 years ago by an ironworker whose name is lost to history. When those gates fail, off-the-shelf parts don’t fit. We fabricate on site: hinge brackets sized to an odd post, pickup points for an opener that was never designed for the gate, reinforcement plates that keep a cracked panel from spreading. Custom welding in San Fernando typically runs $120 to $280 per hour, and we quote the job in writing before the welder ever lights a torch.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in San Fernando
We carry parts and hardware for the opener brands most common in San Fernando, including FAAC, Linear, and Viking. That means when an opener part fails alongside a hinge or rail repair, we don’t schedule two visits. We bring what’s needed on the first trip. For the old gates themselves, we stock heavy-barrel hinges, adjustable latch strikes, and roller assemblies sized for the narrow driveway openings common in this city’s post-war neighborhoods.
Common Gate Parts & Welding Problems We See in San Fernando Homes
- Heat expansion binding: Summer highs here routinely pass 100°F, far hotter than coastal LA. Iron panels expand and bind against posts and roller tracks, so homeowners leave gates ajar just to get them to move. That kills security. We weld panels with the right clearance for San Fernando’s heat, not for a coastal climate.
- Santa Ana wind damage: Wind events funnel through the valley with real force. Unsecured swing gates twist off hinges, stress weld points, and crack older post footings. We’ve seen gates folded back against walls off Maclay Avenue after a bad wind night. Proper hinge reinforcement and a gate stop with a catch makes the difference.
- Deteriorated original footings: Most gate posts in San Fernando sit in concrete poured in the 1950s or 60s. The concrete spalls, water works in, the post shifts, and the gate sags. Replacing the post without addressing the footing just means doing it again in two years. We do both.
- Jammed slide gate rollers: San Fernando’s sandy, wind-blown topsoil gets into roller tracks and grinds them down. A slide gate that starts to drag usually has a collapsed roller bearing, not a motor problem. We replace the roller, clean the track, and get the gate moving quietly again.
Pricing for Gate Parts & Welding in San Fernando, CA
Here’s the reality of pricing in San Fernando. A simple hinge replacement runs $180 to $340. A rail repair runs $150 to $400 per rail. A full post replacement runs $450 to $900, and custom welding runs $120 to $280 per hour. These are the ranges for this market, and the price we quote is the price you pay. No trip charge inside the county. $40 off any repair over $200. A permanent 10% discount for seniors and veterans. And we agree on the number in writing before any work starts, so the invoice doesn’t surprise you at the door. Call (760) 361-6706 for a free estimate on any of this.
One more thing worth knowing about San Fernando specifically. This city is 2.4 square miles, completely surrounded by the City of Los Angeles, and it runs its own building department. Out-of-area gate companies show up assuming they’re operating under LADBS, pull the wrong permit, and discover mid-job that San Fernando City Hall has its own process, its own inspections, and its own fee schedule. Then the work stops while they sort it out. We already know the drill. If your repair needs a permit, we handle it through the right office from the start, so the work doesn’t stall with a rusted hinge half-removed and a gate leaning against your wall.
We Also Serve Cities Near San Fernando
Our crews work throughout the northeast Valley, including Sylmar, Granada Hills, Panorama City, and Sun Valley. If you’re in any of those communities, the same San Fernando team covers your street, with the same live-answer phone line and the same written promise on every job.
Serving San Fernando, CA - Our Local Coverage Area
We’re based in the San Fernando area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in San Fernando
Yes, in most cases a new post footing in San Fernando requires a permit through San Fernando City Hall, not through LADBS. The city’s building department handles it separately, and the process is different from what you’d face elsewhere in the county. We handle the paperwork and scheduling so the work doesn’t stop halfway. Call (760) 361-6706 and we’ll tell you straight what your specific repair needs.
Most likely, yes. San Fernando’s summer temperatures regularly exceed 100°F, which causes wrought iron panels to expand measurably. If your gate clears the ground in the morning and drags by late afternoon, the panel is binding against the hinge post or the gate was welded with insufficient clearance for this climate. We weld heat-specific clearance gaps so the gate swings freely all day. Call (760) 361-6706 for an in-person look.
Yes, and we do this regularly. San Fernando’s wind-blown topsoil works into roller tracks and crushes bearings, which is why slide gates here jam even when the motor is fine. We replace the roller assembly, clean out the track, and often install a debris guard to slow the next buildup. A roller replacement in San Fernando typically runs $150 to $350 depending on the gate size. Call (760) 361-6706 for an exact quote.
We plan for it from the start. On a recent job off Maclay Avenue, a narrow shared driveway meant the vehicle gate had to stay closed for security while we worked. We installed a temporary hoist to hold the gate in place, finished the post footing and hinge replacement in one day, and the neighbor never lost access. That’s the standard in San Fernando, where shared driveways and narrow rights of way are the norm, not the exception. Call (760) 361-6706 and we’ll walk you through how we’d handle your specific site.
Yes, we keep heavy-barrel hinges, adjustable latch strikes, and roller assemblies sized for the narrow driveway openings common in San Fernando’s post-war housing. For parts that don’t exist any more, we fabricate on site with our welding rig. Custom fabrication runs $120 to $280 per hour, and we quote it in writing before starting. Call (760) 361-6706 and tell us what your gate is doing, or not doing.
When a gate fails in San Fernando, waiting isn’t really an option. A gate that won’t close means a driveway that won’t secure, a door a stranger could walk through, and a problem that gets worse and more expensive every day it sits. Call (760) 361-6706. Hal will pick up, or someone from his crew will. We’ll give you an honest answer, a written price, and if you want us there today, we’ll figure out how to make that happen.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving San Fernando since 2001.