Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterElite Gate Parts & Welding in Granada Hills: What to Know First
We handle independent Elite gate parts and welding work across Granada Hills, typically within one to two days of your call. Most hinge replacements, post repairs, and weld failures on Elite gates run between $220 and $680, and we quote the full price before any work begins, so there is no surprise on the invoice. If you own an Elite swing or slide gate in Granada Hills and the metal is cracked, sagging, or the gate simply will not stay in the track, call us at (760) 361-6706. This page is for Granada Hills homeowners who want to understand what is actually wrong with their Elite gate before they spend a dime.
How Elite Products Fail - and How We Fix Them
- Hinge-post fatigue on Elite SL3000 and SL5000 slide gates. The post takes every pound of gate weight every time the operator cycles, and in Granada Hills the dry soil contracts and expands enough that concrete pads shift a fraction of an inch year over year. That small movement transfers straight into the hinge post, and eventually the weld at the base cracks. We cut out the old weld, square the post, and weld it back with the gate still hanging in place, so nothing has to be hauled off.
- Fractured gate frames on Elite Estate series swing gates. These are wide, heavy single-panel gates that were never meant to fight the kind of wind gusts that come through the Santa Susana Pass. When a gust catches a wide panel dead-on, the top rail takes tension and the bottom rail takes compression, and the weak point is almost always the corner weld where the horizontal rail meets the vertical stile. We see the crack start at the inside corner, about half an inch long, and we catch it early with a clean V-groove and a proper weld rather than waiting for the rail to separate entirely.
- Worn gate rollers on older Elite slide models. Granada Hills sits in a dust zone, and that fine dust gets into the roller bearings and grinds them down slowly. You will hear a low rumble first, then a skip as the gate travels. The gate will still move, so people ignore the sound, and by the time they call us the roller has worn square and chewed a groove into the track. We replace the rollers and inspect the rail for flat spots, because putting a new roller on a damaged rail just ruins the new roller.
- Stripped or seized hinge bolts on Elite aluminum gates. Aluminum and steel hardware do not love each other over time. The bolts gall and seize inside the hinge barrel, and a homeowner with a wrench will round the head off trying to free it. We deal with it cleanly: cut the bolt, salvage the hinge if it is still true, and replace the hardware with the correct grade so the next service does not start with a fight.
- Welded repairs that were never right to begin with. We regularly find Elite gates in Granada Hills with someone else’s temporary weld still on them, a cheap short bead laid over a crack without proper cleaning or penetration. The gate ran for six months and then snapped again. We grind the entire area back to clean metal, bevel the joint, and run a full-strength weld that matches the original material thickness. Then the repair goes under the same 90-Day Done Right Promise as everything else we do.
Our Elite Gate Parts & Welding Process
- 1
Call and describe what the gate is doing. Hal will ask you plain questions: where the crack is, what sound it makes, how long it has been doing it. Tell me what it’s doing and I’ll tell you what it needs - no runaround.
- 2
We come to the gate in Granada Hills. There is no trip charge anywhere in the county. We look at the whole gate, not just the cracked part, because a sagging hinge rarely starts at the hinge.
- 3
Parts decision, explained in plain English. Elite OEM parts are generally well-built and worth using when the part matters for fit or operator compatibility. For certain items we will tell you honestly when a quality aftermarket replacement matches or beats OEM for less money. We never use parts that do not belong on your gate.
- 4
The repair happens in your driveway. The gate stays on its posts. We weld on site, replace hinges or rollers as needed, and make sure the gate hangs and travels the way it should.
- 5
We test the full cycle under operator load. Manual gates get opened and closed by hand several times. Automated ones get cycled with the opener to confirm the limit switches and safety edges still behave after the metal work.
- 6
You get the 90-Day Done Right Promise in writing. If anything we touched is not right within 90 days, one call brings Hal back. No fine print, no argument.
What Elite Gate Parts & Welding Costs in Granada Hills
Elite gate parts and welding in Granada Hills depends on the job, but here are the ranges we quote most often:
- Hinge replacement (single hinge, including grinding and welding): $180-$340
- Hinge replacement (full set, heavy Estate or SL-series swing gate): $380-$700
- Gate-post replacement (cut out, reset, weld, finish): $450-$900
- Rail or frame crack repair (weld-only, clean and secure): $220-$480
- Roller replacement (pair, including track inspection): $160-$300
- Custom welding (latch reinforcement, gate extension, operator mounting plate): $150-$400, depending on material and time
What moves the price: gate weight and post depth, how much of the old weld has to be ground out, and whether the gate needs to come off its hinges for the repair. You will know the price before we strike an arc. Call (760) 361-6706 for a free estimate.
Why Granada Hills Homeowners Call Gatewood Fence & Gate for Elite Work
The name on the shop is Hal Gatewood, and the shop is published. He has been fixing gates in this part of the Valley since 2001, and most of his customers can tell you he still shows up when he says he will. We are an independent Elite service provider, not a factory store, so when we tell you a part is worth the OEM price or not worth it, there is no manufacturer cut behind the recommendation. And because we service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing too, we already understand how Elite operators and hardware sit alongside the rest of the gate world. Every job is done by someone who will look you in the eye and hand you a written 90-Day Done Right Promise before he leaves the driveway. That is the whole pitch.
FAQs
If the gate is outside its original warranty period, welding does not affect anything. If it is still under warranty, welding a structural component may void coverage on that specific part, so we will check and tell you before any work is done. As an independent Elite service provider, we are not bound by factory procedures, but we never recommend a repair that quietly costs you a warranty you still hold.
Yes. Most hinge, rail, and frame repairs on Elite swing and slide gates are done with the gate still in place on the posts. Keeping the gate mounted means we work with the actual hang of the gate, so the finished repair is square to how the gate actually sits, not how a shop bench thinks it should sit.
A gate sags in the hinge post, not in the middle. If a previous repair tightened the hinges or re-welded a rail without addressing the post or the hinge-barrel wear, the sag comes back. We start at the post, check the hinges for play, and only then weld or replace what actually failed.
Most parts-and-welding calls in Granada Hills are scheduled within one to two days. If the gate is hanging on one hinge or the post has broken loose, call us and Hal will work it in sooner.
Contact Gatewood Fence & Gate
If your Elite gate in Granada Hills is cracked, sagging, or not rolling clean, call (760) 361-6706. You will get a real person, a straight answer, and a free estimate. The name is on the shop, and the shop is down the road - that is the oldest accountability there is.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Granada Hills and nearby areas.