Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair Services in Sherman Oaks, CA
A gate that won’t open in Sherman Oaks is more than an annoyance. It’s your car trapped behind a steel barrier while the temperature climbs past 100 degrees, or a driveway left wide open because the motor died mid-cycle and the gate never made it back to the closed position. Gatewood Fence & Gate repairs broken gates the same way throughout Sherman Oaks: we come to you, diagnose the actual problem, and fix it on-site with welding and parts carried in the truck. Call (760) 361-6706 and a live person answers, any hour, any day. That’s Hal’s direct line to the shop.
For a deeper look at what we fix and how we price it, see our main Gate Repair in Sherman Oaks page. If the job calls for a full Gate Installation in Sherman Oaks or work on the Gate Motor & Opener in Sherman Oaks, those pages explain the process in plain terms.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Why Sherman Oaks Homeowners Choose Gatewood Fence & Gate
Hal Gatewood has been fixing gates since 2001. His name is on the shop, his address is published, and his phone rings in his pocket. When you call for gate repair in Sherman Oaks, you’re not routed to a queue. You get Hal or a member of his crew, and the person who answers is the person who shows up. Every job carries the 90-Day Done Right Promise in writing: if it’s not done right, one call brings him back, no wrangling about what was covered.
Sherman Oaks homeowners call us from the flats south of the 101 and from the hills above Ventura Boulevard, from the ranches near Dixie Canyon and the gated courts off Longridge Avenue. We know what those driveways do to a gate. We’ve welded hinges on curving hillside approaches where the gate binds against the grade, and we’ve re-set posts on flat valley lots where the original footer wasn’t poured deep enough for a modern operator. We repair gates other companies want to haul away and replace. Often the gate only needs a weld, a hinge, a capacitor, or a limit switch: parts that cost far less than the quote for a whole new motor.
We’re not a national outfit. We never will be. You can look up our license, drive to the shop, or shake Hal’s hand at the hardware store. That’s the oldest accountability there is.
Gate Repair Services We Offer in Sherman Oaks
Gate Repair
A sagging gate sags in the hinge post, not in the middle. That’s where we start. We weld on site, re-set posts, replace rollers, and true the frame so the gate hangs square on its hinges. Show me the gate closing on its own and I’ll show you where it’s failing. Learn more about our Gate Repair in Sherman Oaks.
Gate Installation
New gates need posts set plumb and deep, hinges sized to the weight of the panel, and an operator matched to the sweep of the gate. On Sherman Oaks hillsides, we measure the driveway grade before we order a single part. Learn more about our Gate Installation in Sherman Oaks.
Gate Motor & Opener
We service nine major brands including LiftMaster, FAAC, BFT, and Mighty Mule. Valley heat cooks capacitors; Santa Ana winds put lateral loads on opener arms and hinge pins. We carry common boards, capacitors, receivers, and remotes so we can usually fix the opener in one visit. Learn more about our Gate Motor & Opener in Sherman Oaks.
Gate Access Control
Keypads, telephone entry systems, loop detectors, and intercoms all fail in predictable ways. We diagnose the specific component rather than selling you a whole new system. We’ll wire it, program it, and show you how to use it before we leave.
Gate Parts & Welding
We keep hinges, rollers, brackets, weld-on gate hardware, and steel stock on the truck. If your gate needs a cracked weld repaired or a broken hinge replaced, we do it in your driveway, not in a shop forty miles away.
Neighborhoods We Serve in Sherman Oaks
We cover Sherman Oaks from the Ventura Boulevard corridor to the hills south of Mulholland Drive, and from the 405 east to the 170. Typical response is the same day or the next morning for most repair calls, depending on what you need. We regularly work in:
- Sherman Oaks Hills (south of Ventura Blvd)
- Chandler Estates
- The flats around Hazeltine and Kester Avenues
- The neighborhoods off Van Nuys Blvd near the 101
- The hillside streets around Longridge Avenue and Dixie Canyon Avenue
Why Sherman Oaks’s Climate & Housing Affect Gate Repair
Sherman Oaks splits into two distinct terrain types, and each one breaks gates in its own way. The flat valley floor, built out with postwar ranch homes between the 101 and Ventura Boulevard, sits on dense tract layouts where original gate posts from the 1950s and 1960s were poured shallow. When a homeowner adds an automatic opener during a renovation, the post flexes under the operator’s torque. We see that every week: a new motor bolted onto a post that was never meant to move a gate. The fix is re-setting the post deeper and adding a steel core, not replacing the operator.
Up in the Sherman Oaks Hills, the problem reverses. Driveways climb steeply to the door, curving as they go. A standard swing gate on hinges will bind against the rising asphalt at the bottom of its arc. Streets like Longridge Avenue and Dixie Canyon Avenue are full of gates that drag or stall halfway open. On those calls, we measure the driveway grade first, because the answer is often a cantilever slide gate or a gate rebuilt with offset hinge geometry. Neighboring flat Valley cities like Van Nuys almost never see this problem. Sherman Oaks, by contrast, sees it constantly.
Then there’s the heat. Sherman Oaks sits deep in the San Fernando Valley heat pocket, where summers routinely push 105 to 110 degrees: fifteen to twenty degrees hotter than the Westside. Those temperatures shorten capacitor life in gate openers, crack the UV-exposed insulation on operator wiring, and cause iron gate frames to rack as they expand and contract across the hot season. Add Santa Ana winds funneling through the Valley and putting repeated side loads on gate posts and hinge pins, and you have a climate that works gates hard. A gate that was fine in May can bind in August and trip its obstruction sensor in September.
And there’s a historical wrinkle we still run into. The 1994 Northridge earthquake, centered just miles away, shifted and cracked concrete driveway aprons and gate post footings all over Sherman Oaks. Many gates were re-hung or shimmed after the quake, and the posts were left subtly out of plumb. Three decades later, those same posts cause modern automatic operators to bind or stop midway. We check for post-plumb on every repair call in Sherman Oaks because it so often turns out to be the thing everyone else missed.
Pricing for Gate Repair in Sherman Oaks
Honest pricing means you hear the number before work starts, and the number doesn’t change when the job is done. That’s the deal, in writing, every time. Typical repair prices in Sherman Oaks run like this:
- Minor weld or hinge repair: $150 to $350
- Motor capacitor or limit switch replacement: $180 to $320
- Gate opener board replacement: $250 to $550 depending on brand
- Post re-set or reinforcement: $400 to $900 depending on depth and concrete work
- Full automatic opener installation: $1,800 to $4,200 depending on gate weight, brand, and access control
Every quote is firm. No trip charge inside the county. Seniors and veterans get a permanent 10% off. And any repair over $200 gets $40 off, no haggling required. Call (760) 361-6706 for a free estimate on gate repair in Sherman Oaks.
Service Area - Cities Near Sherman Oaks
We repair gates across the San Fernando Valley. If you’re in Van Nuys, Encino, Tarzana, or Panorama City, you’re covered. Flat-lot repair, hillside gate conversion, motor service in the heat: same crew, same promise.
Serving Sherman Oaks, CA - Our Local Coverage Area
We’re based in the Sherman Oaks area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Sherman Oaks
Most gate repairs in Sherman Oaks run between $150 and $900 depending on whether it’s a weld, a hinge, a post re-set, or an opener component. A written quote is agreed before work starts, and the price doesn’t change at the door. Call (760) 361-6706 for an exact number: estimates are free, and there’s no trip charge inside the county.
For most gate repair calls in Sherman Oaks, yes. We schedule same-day or next-morning service for broken hinges, failed openers, and gates that won’t close. Call (760) 361-6706 and a person answers. We’ll tell you when we’ll be there and then show up.
We do. The hillside streets off Longridge Avenue and Dixie Canyon Avenue have steep, curved driveways that bind standard swing gates against the grade. We measure the driveway slope, the gate weight, and the hinge geometry before recommending a fix, which is often a slide-gate conversion or a re-hinged gate with offset pivots. We’ve done it many times, and we’ll be honest about what works.
Yes, we install and service the full system: motor, opener, safety edges, loop detectors, keypads, and the low-voltage power run. We service LiftMaster, FAAC, BFT, and Mighty Mule openers, and we carry common boards, receivers, and capacitors in the truck. We’ll diagnose the exact failed component and replace only what needs replacing.
It covers every repair and installation we do. If something isn’t done right within 90 days, one phone call brings Hal back to make it right. No fine print, no runaround. That’s the promise, and it’s in writing on every job.
Need a gate fixed in Sherman Oaks? Call (760) 361-6706 and tell us what the gate is doing. Hal or a member of his crew will answer, give you a straight answer, and show up with the truck stocked for the job. The name is on the shop, and the shop isn’t far away.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, fixing gates across the Valley since 2001.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Sherman Oaks Customers Say
"Beautiful gate and solid work. The build took about three weeks longer than the estimate because he was waiting on the ironwork, and I would rather have known that at the start than found out along the way."
- Beatrice Nwosu"Fitted a keypad and an intercom so my mother can let carers in without coming down the drive. He set it up and then made her practise with it until she was comfortable."
- Lucinda Marchbanks"Hundred and forty feet of cedar privacy fence, all posts set in concrete, all of it dead level on ground that is anything but. He walked the line with me twice before a single hole was dug."
- Judith Stallworth