Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Tarzana
Gate parts and welding in Tarzana usually means one of two things: a hinge that finally let go after thirty summers, or a homeowner standing in the driveway wondering whether the whole gate needs to be hauled off. Most of the time, it doesn’t. We cut out the broken section, weld in new steel, replace the hinge or roller that actually failed, and the gate stays right where it belongs: on your property, not on a flatbed. Hal Gatewood’s been doing exactly this since 2001, and he’d rather fix a gate in Tarzana than sell you a new one you don’t need. Call (760) 361-6706 and a live person answers, any hour.
Why Gatewood Fence & Gate Is Tarzana’s Preferred Gate Parts & Welding Company
Around here, a lot of our work comes from homeowners who already paid somebody else to fix the same gate twice. Tarzana’s hillside properties punish sloppy work faster than most places in the Valley. When we weld a hinge post on a slope near Braemar Country Club, we’re not just matching the old bolt holes. We check the grade the gate actually swings against, because a gate that sags into the hill is going to tear out a hinge every couple years until somebody addresses the real problem. That’s the difference between a parts swap and a repair that holds.
Our reputation in Tarzana comes from doing the job in your driveway, not in a shop across town. Hal’s name is on the company and on the invoice. The person who shows up in Tarzana is the person who stands behind the work, and the 90-Day Done Right Promise is in writing on every ticket, not buried in a service agreement. If something’s not right, one call brings us back. No runaround, no “that’s a different department.”
We answer the phone around the clock. Not a voicemail, not a call center. You’ll talk to a person who can tell you whether the hinge we need is likely on the truck or has to be ordered. For Tarzana jobs, we coordinate scheduling through our Los Angeles office and keep common parts stocked locally, so we’re not making you wait on a box from Ohio. You can also drive to the shop and look Hal in the eye. The address is published and so is the license number, and that’s the oldest accountability there is.
Our Gate Parts & Welding Services in Tarzana
We handle the full range of Gate Parts & Welding work Tarzana homes need, from small hardware fixes to structural steel repair. Here’s what we do most often in this part of the Valley.
Hinge Replacement
A gate sags in the hinge post, not in the middle, and that’s where we start. On Tarzana’s older ranch-style homes, we regularly find hinges that have been greased for years while the real problem was a post that shifted or a weld that cracked. We replace heavy barrel hinges, weld-on strap hinges, and adjustable post hinges, then set the gate back to plumb. If the hinge post itself is the issue, we address that before we bolt on new hardware. Fix the panel without the post and you’ll fix it twice.
Post Replacement
This is the biggest job in Tarzana’s hillside neighborhoods, and the one most homeowners don’t see coming. Concrete pillar posts on 1980s and 90s estate gates crack at the footing over time, and once a post moves even half an inch, the gate binds, the operator strains, and the latch misses the strike. We pull the old post, weld a new steel footing or set a steel post in concrete, and re-anchor the gate. When the post comes out near a slope, we dig to solid bearing and we don’t rush the cure. Nobody wants to redo a post job on a driveway with a 10-degree grade.
Rail Repair
Slide gates on Tarzana’s flat valley floor take a beating from the heat. Aluminum track warps in July, and a warped rail will chew through rollers in one season. We straighten bent rail sections, weld in replacement rail, and re-align track so the gate rolls without fighting itself. On older retrofitted gates, we often find the original rail was sized for a lighter gate than what’s hanging on it now. We’ll tell you straight what needs replacing and what still has years left in it.
Custom Welding
This is where Tarzana’s estate gates separate the parts-swappers from a real weld shop. We fabricate and weld on site: cracked wrought-iron pickets, broken scrollwork, gate extensions, rack and pinion rail, operator mounting plates, and reinforcement gussets. Hal welds in your driveway, so the gate stays hung and the repair matches the existing steel. If you have an ornamental gate that’s been in the family since the 1980s, we’d much rather rebuild the broken section than tell you to go shopping for a new one.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Tarzana
We service and stock parts for the operators Tarzana homeowners actually have on their gates. That includes FAAC, BFT, Linear, and Viking, along with LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your gate opens with a remote, there’s a good chance we carry the board, clutch, or limit switch for it. We keep common parts stocked for Tarzana customers and when something’s not on the shelf, we get it ordered the same day we diagnose.
Common Gate Parts & Welding Problems We See in Tarzana Homes
- Hillside gates reversing mid-cycle. Operators sized for flat ground strain against gravity on sloped driveways south of Ventura Boulevard. The clutch wears out in two or three seasons, and the gate gets flagged as “broken” when the real fix is a torque recalculation or an operator sized for the grade.
- Warped aluminum track on slide gates. Tarzana’s July and August heat regularly pushes past 105°F. Aluminum rail expands, warps, and binds the gate, and unshaded driveway gates on the valley floor get it worst. We replace or straighten the rail and set new heat-hardened rollers.
- Cracked post footings on estate swing gates. Ornamental wrought-iron gates are heavy, and 1980s concrete footings near Braemar Country Club are only just now failing. A cracked footing lets the gate drop, the latch miss, and the hinges take load they were never meant to carry.
- Santa Ana wind damage on exposed hillside gates. Autumn gusts hit swing gates on Tarzana’s south-facing slopes hard. Hinge bolts loosen, latch strike plates bend, and a gate that was shutting clean in September is rattling by November.
Pricing for Gate Parts & Welding in Tarzana, CA
Here’s what we see in Tarzana’s market right now. Hinge replacement typically runs $220 to $420 per hinge, depending on the weight of the gate and whether we’re welding new mounts or reusing existing bolt patterns. Post replacement is a bigger lift: $600 to $1,400 per post when a footing has cracked and we’re setting new steel. Rail repair on a slide gate usually lands between $180 and $450 for straightening and re-alignment, with welded-in replacement sections adding material cost. Custom welding runs $95 to $150 per hour plus steel, and most repair welds take under two hours. Every price is quoted and agreed before any work starts. Before I turn a wrench or strike an arc, you know the number. Call (760) 361-6706 for a free estimate, and remember: $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans.
We Also Serve Cities Near Tarzana
We’re local to the San Fernando Valley and regularly work in Encino, Reseda, Canoga Park, and Sherman Oaks. The hills west of Sepulveda Pass hide gate problems you’ll rarely see in flat neighborhoods. If you’re nearby and the gate’s acting up, give us a call. We know these streets, and we’re probably already working a job a few blocks over.
Serving Tarzana, CA - Our Local Coverage Area
We’re based in the Tarzana area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Tarzana
The operator was almost certainly sized for flat ground, not for a driveway that climbs toward the house. On a slope, the motor fights gravity every time the gate opens, and the clutch wears out fast. We check the actual slope angle and recalculate the torque setting, and often the fix is a new clutch and a motor rated for the grade rather than a whole new operator. Call (760) 361-6706 and we’ll diagnose it on site.
Unless the steel itself is rusted through, you need a hinge and post assessment, not a new gate. Most sagging gates in that neighborhood are a post that cracked at the footing or hinges that have worn egg-shaped. We weld new hinge mounts, replace the post footing if needed, and set the gate back to plumb. A new gate would cost five times as much and wouldn’t fix the post.
Test them yourself: start the gate closing and pass your hand through the beam. If the gate doesn’t stop and reverse, the photocells are dead. Tarzana heat bakes circuit boards and cracks the plastic housings on older units, and a gate without working safety eyes is a serious hazard, especially with kids or pets around. We replace them in about an hour. Call (760) 361-6706 and we’ll test them while we’re out.
We can weld a new rack onto your existing gate in most cases. If the gate’s steel frame is sound, there’s no reason to replace the whole thing. We’ll cut out the worn rack section or weld a new length along the bottom rail, then re-mesh the pinion gear and set the limits. It’s a measured job, not an emergency swap, and we’ll give you a written price before we start.
Heat-hardened nylon or sealed steel-bearing rollers hold up best in Tarzana’s sustained summer heat. Cheap nylon rollers soften and warp, and unsealed steel rusts by Christmas. We stock heat-rated rollers and replace them before they eat your track. A gate that rolls clean doesn’t strain the motor, and that’s the cheapest repair you’ll never have to make. Call (760) 361-6706 for a free estimate.
Contact Gatewood Fence & Gate in Tarzana
If your gate’s making noise it didn’t make last summer, or the latch missed this morning for the third time this week, that’s a repair telling you it’s due. Call Hal Gatewood at (760) 361-6706 for a free estimate. We’ll put eyes on the gate, tell you honestly what it needs and what it doesn’t, and quote the price before anything gets unbolted. You can also drive to the shop and look us in the eye. The name’s on the door, and the warranty’s on the invoice.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Tarzana and the San Fernando Valley since 2001.