Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Encino
If you need a new driveway gate or a pedestrian gate in Encino, you’re looking at $2,800 to $9,500 for a typical automated installation, with work usually scheduled within 7 to 14 days after your free measure. We cover every corner of Encino, from the ranch homes south of Ventura Blvd to the big hillside estates off Hayvenhurst and White Oak. Hal Gatewood has been building and hanging gates since 2001, and the crew knows exactly which operators survive on a sloped Encino Hills driveway and which ones cook themselves in August. Call (760) 361-6706 and a live person answers, day or night.
Key takeaways:
- Full driveway gate installations in Encino typically run $2,800 to $9,500 depending on gate width, automation, and hillside footing work.
- We quote a firm price before any work starts, and that price is the price.
- Encino’s heat and hillside grades kill undersized operators. We spec for the driveway you actually have.
- Every installation carries the 90-Day Done Right Promise in writing.
Why Gatewood Fence & Gate Is Encino’s Preferred Gate Installation Company
We’re not a national outfit with a rotating cast of subcontractors. The name on the shop is Hal Gatewood, and he’s been owner-operator since 2001. When you call about a gate in Encino, you talk to a person who has driven Ventura Blvd, climbed driveways off Amestoy, and looked at hundreds of gate installations between Rancho Estates and Lake Encino. The guy who answers the phone knows what a swing gate on a 12% grade does to a hinge post after one summer. That kind of knowledge doesn’t come from a training manual.
Our Gate Installation work throughout the Encino area has built us a strong local reputation. Homeowners keep our number because we show up when we say we will, we charge what we quoted, and if something isn’t right within 90 days, one call brings Hal back to make it right. No runaround. Seniors and veterans get a permanent 10% discount, and we never charge a trip fee inside the county. Some companies dodge the phone. We answer it, 24/7.
Our Gate Installation Services in Encino
Driveway Gate Installation
A driveway gate on Encino’s sloped lots is a different animal than one on flat ground. We set hinge posts in deep footings with rebar, size operators for the grade and the gate’s actual weight, and make sure the whole swing doesn’t fight gravity from day one. North of Ventura, we regularly see 1980s-era posts pulled out of plumb from undersized operators. Our installs don’t repeat that mistake. Expect $3,500 to $9,500 for a fully automated driveway gate, installed and tested.
Pedestrian Gate Installation
Pedestrian gates in Encino serve a lot of the older ranch homes on the valley floor, many built in the 1950s and 60s. We hang them square, weld the hinges on site if that’s what the layout needs, and add maglocks or strike hardware when they’re tied into an access system. A standard welded steel pedestrian gate runs $900 to $2,200 depending on width and hardware.
Sliding Gate Installation
Cantilever and track-style sliding gates suit some of the longer, flatter Encino driveways where a swing arc would eat too much space. We install them with proper track drainage, because Santa Ana winds blow leaf litter and grit into slide-gate tracks all autumn. A typical automated sliding gate in Encino runs $4,000 to $8,500, including operator and safety loops.
Swing Gate Installation
Swing gates are the most common style we install in Encino, especially the double swing gates on hillside estates. Dual gates need matched operators, or the wind catches one leaf and racks the whole frame. We install paired operators with a synchronized control board, and we size the rams for the weight of the panels plus the slope. Double swing gate installations typically run $4,500 to $9,500.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Encino
We’re certified to work on LiftMaster, FAAC, BFT, and Mighty Mule equipment, among others. If you already have an operator you like, we’ll build around it. If you want a recommendation for a hillside install, we lean toward LiftMaster’s higher-torque swing operators because they hold up to Encino’s heat better than most. We keep parts and boards stocked for fast turnaround, and we weld on site, so a cracked gate post doesn’t mean the gate has to leave your driveway.
Common Gate Installation Problems We See in Encino Homes
Encino’s housing stock and climate create some very specific failure patterns. Here’s what we see again and again:
- Heat-killed operator boards. July and August push past 110°F in Encino, and circuit boards in older LiftMaster and Viking units just cook. The fix is an operator rated for continuous Southern California heat, not the cheapest model that fits.
- Hillside hinge posts leaning out of plumb. Gravity never quits. We open up the old footing, find it’s 18 inches deep with no rebar, and wonder how it lasted 30 years. Our replacement posts go 24 inches plus, tied with steel.
- Undersized operators on graded driveways. A 1980s swing operator that was marginal on flat land has been stressed on a hill for decades. Motor burnout on these hillside properties is one of the most common repeat calls we get in the corridor north of Ventura.
- Santa Ana damage to gate frames. The wind events off the ridge lines above Encino Hills rack gate frames and throw debris into slide tracks. Hinge welds take the brunt. We inspect and re-weld before it becomes a full-frame replacement.
Pricing for Gate Installation in Encino, CA
A pedestrian gate in Encino runs $900 to $2,200. A standard single driveway swing gate with automation is $2,800 to $5,500. Double swing gates on wide hillside driveways run $4,500 to $9,500, and a full sliding gate installation typically lands between $4,000 and $8,500. The biggest cost drivers are gate width, whether we’re re-setting posts on a sloped driveway, and operator sizing. We quote a fixed price before work starts. That number doesn’t change at the door. Call (760) 361-6706 and we’ll measure your driveway and hand you a written price.
We Also Serve Cities Near Encino
Our crews work throughout the San Fernando Valley and into the hills beyond. If you’re in Tarzana, Reseda, Sherman Oaks, or Van Nuys, we’ll come out and quote your gate installation the same way we do for Encino neighbors: a live person on the phone, a free measure, and a firm written price.
Serving Encino, CA - Our Local Coverage Area
We’re based in the Encino area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Encino
Salt air corrosion on Encino gate hardware accelerates wear roughly 2 to 3 times faster than inland LA, eating through galvanized post plates and corroding the wire terminals inside operator enclosures. We use stainless steel fixings and sealed operator housings on coastal Encino estates, and we weld on site so the galvanic points where dissimilar metals meet are protected before installation.
Hillside operators fight gravity every time the gate moves. An undersized motor that would last 15 years on a level driveway works twice as hard on a 10 to 15 percent grade, so windings burn out and boards fry in Encino’s summer heat. We spec higher-torque operators rated for sloped installations, which is the correct fix on nearly every hillside property we quote.
On hillside properties, the hinge post is usually the first to fail. It leeches out of an undersized footing under the gate’s weight, which throws the gate out of square, which then strains the operator and cracks the welds. That’s why our installations replace post footings before anything else. Call (760) 361-6706 to have us measure and quote, and we’ll tell you exactly what you’re looking at.
Yes. UL 325 entrapment protection is mandatory equipment, but on a sloped Encino driveway a gate that loses its reversing sensor can close with more force than the same gate on level ground. We install current sensing and photo-eye protection on every automated gate we hang in Encino, and on steep lots we add an extra set of photo eyes across the gate opening.
They usually do. Many 1950s and 60s Encino ranch homes had lightweight chain link or tube steel gates on shallow footings. New spec houses off Ventura Blvd are putting in heavy wrought-iron panels weighing hundreds of pounds. Those need poured 24-inch-plus footings with rebar ties, or the posts will lean within a few years.
Call Gatewood Fence & Gate for Gate Installation in Encino
Up in Encino Hills off Hayvenhurst, we replaced a 1987 Viking swing gate operator on a sloped driveway where the original posts had pulled 3 degrees out of plumb. We re-set the hinge posts in 24-inch footings with rebar, upgraded to a LiftMaster LA500 24VDC swing operator with an onboard loop detector, and added safety photocells across the gate opening. That gate now swings against the grade without sag correction for the first time in a decade.
That’s the kind of job we do in Encino every week. If your gate is sagging, your operator is dead, or you’re building something new, call (760) 361-6706 for a free estimate. Hal’s name is on the shop, his address is published, and he’ll be the one quoting your job in person. The 90-Day Done Right Promise is in writing on every installation. No fine print, no call center, no runaround.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Encino since 2001.